Craftsman Laser Trac Drill Press 2/3 HP Parts: What Owners Search For and Where to Find Them
The Craftsman Laser Trac drill press (model No. 229250) is a 15-inch, 2/3 HP floor press that Sears sold with one distinguishing feature: a built-in laser crosshair system meant to show you exactly where the bit will land before you drill. It worked well enough when new. The problem owners run into now is parts, and the laser module specifically.
If you are searching for Craftsman Laser Trac drill press 2/3 HP parts, this article covers what the machine actually is, which parts are most commonly needed, and where to find them.
Confirmed Specs: Model 229250
| Specification | Value |
|---|---|
| Model number | 229250 |
| Swing | 15 inches |
| Motor | 2/3 HP |
| Speeds | 12 |
| Speed range | 250 to 3,100 RPM |
| Laser | Built-in crosshair laser guide |
| Runout | 0.004 inches (spec) |
| Voltage | 120V, single-phase |
The 229250 is a 15-inch swing floor-standing press. Its 12 speeds cover a wide range for drilling wood, plastic, and light steel. The laser guide projects two lines that intersect at the centerpoint of the bit’s path.
Which Parts Do Owners Search For Most?
Belt. Like any step-pulley drill press, the 229250 uses V-belts between the motor and the spindle pulley stack. These are A-section belts and are the most commonly replaced wear item. Search eReplacementParts.com with model number 229250 to find the correct sizes. Generic A-section belts from any major manufacturer will work if OEM is unavailable.
Laser module. This is the part owners search for hardest and find least often. The laser unit is a proprietary module specific to the Laser Trac system. When it fails (as the diode ages or the wiring connector corrodes), the module is difficult or impossible to source new.
Depth stop assembly. The depth stop rod and collar see significant use. Replacement parts can sometimes be sourced through eReplacementParts.com or by having a machinist turn a compatible piece.
Chuck. The 229250 uses a standard Jacobs-style taper chuck. A quality 1/2-inch or 5/8-inch replacement in the correct taper is widely available.
Spindle return spring. A common failure point on any heavily used drill press. Check eReplacementParts.com or Sears PartsDirect with the model number.
Table lock assembly. Sears PartsDirect and eBay are the practical sources here.
Where to Find Parts
Sears PartsDirect (searspartsdirect.com). Still the most direct source for official documentation. Search “229250” to pull up the parts diagram.
eReplacementParts.com. Search the model number “229250” directly. This site often has stock that Sears PartsDirect no longer carries.
eBay. The best source for used or new-old-stock parts, particularly the laser module. Search “Craftsman 229250” and “Craftsman Laser Trac drill press.”
ManualsLib.com. For the service manual and parts diagram, which you need before ordering any part to confirm part numbers.
The Honest Flaw: The Laser Module
The laser alignment system on the 229250 is a separate electrical module from the drill press drive system. When it fails, and it frequently does as the machine ages, the press continues to operate perfectly as a drill press. The laser is simply dark.
The laser module is proprietary to the Laser Trac design, OEM replacements are no longer in production, and used modules from eBay are the only realistic source for a like-for-like repair. The alternative is to remove the laser housing entirely and use a center punch and layout dye for hole location. The press does not need the laser to drill accurate holes.
If you are buying a used 229250 specifically because of the laser feature, test the laser before purchase.
Who Should Skip a Full Rebuild?
If the motor or spindle housing is damaged, a full rebuild stops being practical. The 229250 is a vintage machine with discontinued OEM parts, and a damaged motor or cracked column makes the repair outrun the machine’s practical value.
Parts Summary Table
| Part | OEM Availability | Best Source |
|---|---|---|
| Belt (A-section) | Generic available | eReplacementParts.com, bearing supply |
| Laser module | Discontinued | eBay (used/NOS only) |
| Depth stop | Limited | eReplacementParts.com, machinist |
| Chuck (Jacobs taper) | Generic available | Any tooling supplier |
| Return spring | Limited | eReplacementParts.com |
| Table lock | Limited | eBay, Sears PartsDirect |
Conclusion
The Craftsman Laser Trac drill press model 229250 is a 15-inch, 12-speed, 2/3 HP floor press with a laser crosshair system that is now the hardest part to service. The press itself, belts, chuck, springs, and table components, is serviceable through eReplacementParts.com and eBay. The laser module is effectively out of production. When it fails, the press still works fine as a drill press.
FAQ
What is the model number of the Craftsman Laser Trac drill press? The primary model is 229250. Confirm yours against the data plate on the column.
Where can I find parts for the Craftsman 229250 drill press? eReplacementParts.com (search “229250”), Sears PartsDirect, and eBay.
Can I replace the laser module on the Craftsman Laser Trac drill press? OEM modules are discontinued. Used and new-old-stock units occasionally appear on eBay.
Does the Craftsman Laser Trac still work if the laser fails? Yes. The laser is a separate system. The drill press motor, quill, and spindle operate independently of the laser module.
What belt does the Craftsman 229250 use? A-section V-belts. Check the parts diagram on eReplacementParts.com for specific sizes.
What chuck taper does the Craftsman 229250 use? A Jacobs-style taper, most commonly JT33. Confirm before ordering a replacement.
How many speeds does the Craftsman Laser Trac have? 12 speeds, ranging from 250 to 3,100 RPM.
What is the runout spec? 0.004 inches.
Where can I download the Craftsman 229250 manual? ManualsLib.com. Search “Craftsman 229250 drill press.”
References
- Craftsman model 229250 specs: Sears PartsDirect: searspartsdirect.com
- eReplacementParts.com: ereplacementparts.com
- ManualsLib.com: manualslib.com
- WEN Products Drill Press FAQs: wenproducts.com
- OSHA 29 CFR 1910.147, Lockout/Tagout
- CCOHS, Drill Press Safety: ccohs.ca
