SKIL 3320-01 3.2 Amp 10-Inch Drill Press: Specs, Performance, and Current Alternatives
The SKIL 3320-01 3.2 amp 10-inch drill press was one of the more capable machines in its class when it was in production, offering a genuine cast iron table and five step-pulley speeds. It is now discontinued, which means no factory parts, no warranty, and an increasingly thin used-market supply. Here is what the machine actually does, where its limits are, and what to buy if you need something that is currently supported.
Confirmed Specs: SKIL 3320-01
| Spec | Value |
|---|---|
| Swing | 10 inches |
| Motor | 3.2 amps |
| Speeds | 5 (570 to 3,050 RPM) |
| Speed system | Step-pulley (belt-driven) |
| Chuck | 1/2-inch keyed |
| Quill travel | 2 inches |
| Table | Cast iron, tilting |
| Depth stop | Yes |
| Spindle taper | 33JT |
| Weight | Approximately 34 lbs |
The five-speed range from 570 to 3,050 RPM gives reasonable coverage for both large-diameter spade bits in softwood at the low end and small twist bits in hard materials at the high end. The cast iron table is a genuine differentiator: many competing benchtop presses in this footprint used stamped steel tables.
What the SKIL 3320-01 Can and Cannot Do
What it handles well:
- Drilling through softwood, hardwood, and plywood with standard twist bits up to 1/2 inch
- Forstner bits in wood at appropriate low speeds
- Light drilling in thin aluminum or similar non-ferrous sheet metal
- Repetitive drilling to a consistent depth using the depth stop
Where it falls short:
- Quill travel is 2 inches. Anything thicker requires repositioning the workpiece.
- The 3.2-amp motor will bog down on continuous heavy cuts in hardwood or on thick metal.
- No factory support. If you need a part, you are on your own.
Honest Flaw: No Parts Support
The SKIL 3320-01 is discontinued. SKIL does not manufacture or distribute OEM replacement parts for this machine. If the V-belt wears out, you need to measure and source a generic replacement. If the chuck fails, you are sourcing a compatible 33JT chuck from a third-party supplier. If the motor fails, you are looking at eBay or scrapping the machine.
eReplacementParts.com may still list some legacy parts for the 3320-01.
This is the single biggest reason to think carefully before buying a used 3320-01 over a current machine.
Who Should Skip the SKIL 3320-01
- Anyone who needs active warranty support.
- Anyone who needs quill travel beyond 2 inches.
- Anyone who cannot source a belt or chuck independently if the originals fail.
- Anyone buying new: the 3320-01 is not available new from authorized retailers.
The Current Replacement: SKIL DP9505-00
SKIL’s current 10-inch drill press is the SKIL DP9505-00, a 6.2-amp machine with five speeds and active factory support.
The DP9505-00 nearly doubles the motor amperage of the 3320-01 (6.2A versus 3.2A), which translates to noticeably more torque under load. It also improves on quill travel (3-1/8 inches versus 2 inches), which is a meaningful upgrade for anyone who found the older machine limiting on thicker stock.
Comparison Table
| Feature | SKIL 3320-01 | SKIL DP9505-00 |
|---|---|---|
| Swing | 10 in | 10 in |
| Motor | 3.2 amp | 6.2 amp |
| Speeds | 5 (570-3,050 RPM) | 5 |
| Chuck | 1/2 in keyed | 1/2 in keyed |
| Table | Cast iron | Cast iron |
| Quill travel | 2 in | 3-1/8 in |
| Status | Discontinued | Current |
| Warranty | None | Active |
| Parts | Secondary market | Factory supported |
Is a Used SKIL 3320-01 Worth Buying?
If you find one in good working order with an intact belt, chuck, and table, and you understand that you are responsible for sourcing any future replacement parts, a used 3320-01 can still be a serviceable shop press. But if the machine needs work, or if you are building out a shop where downtime matters, buy the SKIL DP9505-00 instead.
Key Takeaways
- The SKIL 3320-01 is a 10-inch, 3.2-amp, 5-speed benchtop drill press with a cast iron table. It is discontinued.
- No factory parts or warranty support remains. All service is self-sourced.
- The quill travel is only 2 inches, which limits the machine to thinner stock.
- The SKIL DP9505-00 is the current replacement with 6.2A, 3-1/8-inch quill travel, and active support.
FAQ
Is the SKIL 3320-01 still being made? No. It is discontinued.
What are the speeds on the SKIL 3320-01? Five speeds ranging from 570 to 3,050 RPM via a step-pulley system.
What size chuck does the SKIL 3320-01 use? A 1/2-inch keyed chuck with a 33JT spindle taper.
Can I get replacement parts for the SKIL 3320-01? OEM parts are not factory-supported. Check eReplacementParts.com for any remaining stock.
What is the quill travel on the SKIL 3320-01? Two inches.
What replaced the SKIL 3320-01? The SKIL DP9505-00.
Is the SKIL 3320-01 good for metal drilling? It handles light drilling in thin non-ferrous metals. Not suited for heavy or repeated metal drilling.
Should I buy a used SKIL 3320-01? Only if it is in good working condition and you are comfortable sourcing generic parts independently.
References
- SKIL product pages: skil.com
- eReplacementParts.com: SKIL drill press parts: ereplacementparts.com
- OSHA Drill Press Safety: osha.gov
- CCOHS Drill Press Safety: ccohs.ca
